点击图片查看原图
L6C天平称50kg传感器L6C-C3-50KG-2B称重传感器：公司有各类称重模块，化厂家配料称重模块，防爆场合效应釜防爆称重模块，搅拌作业专用动态高精度称重模块，各类大型仓秤大吨位称重模块，物流线高精度小量程称重模块，
称重传感器的输出信号读出电路,不应和能发生强烈干扰的设备及有可观热量发生的设备放在同一箱体中,若不能确保这一点,则应思虑在它们之间设置障板阻隔之,并在箱体内安顿电扇.所有通向发现电路或从电路引出的导线,均应选用屏蔽电缆.
有3只传感器是全并联接法,传感器自己是4线制,但在接线盒内换成6线制接法.用以丈量称重传感器输出信号的电子线路,应尽没准配置独立的供电变压器,而不要和接触器等设备共用同一主电源.称重传感器的信号电缆,不好强电电源线或控制线并行安置.若它们有必要并行放置,那么,它们之间的距离应如旧在50CM以上,并把信号线用金属管套起来.
不管在何种情况下,电源线和控制线均应绞合起来,合程度50转/米,若称重传感器信号线需要延伸,则应选用独特的密封电缆接线盒.
若不必此种接线盒,而选用电缆与电缆直白对接,则应对密封防潮极端予以留意,接好后应查验绝缘电阻,且需达到规范(2000~5000M),必要时,应从头标定传感器.若信号电缆线很长,又要确保很高的丈量精度,应思索选用带有中继放大器的电缆抵偿电路.
ZSF-A-10t,ZSF-A-15t,ZSF-A-20t,ZSF-A-25t,ZSF-A-30t,ZSF-A-40t,ZSF-A-50t。ZSF-SS-10t,//ZSF-SS-15t,ZSF-SS-20t,ZSF-SS-25t,ZSF-SS-30t,ZSF-SS-40t,ZSF-SS-50t。ZSF-D-10t,ZSF-D-15t,ZSF-D-20t,ZSF-D-25t,ZSF-D-30t,ZSF-D-40t,ZSF-D-50t,ZSL-1t,ZSL-2t,ZSL-3t,ZSL-5t,ZSL-10t,ZSL-15t,ZSL-20t,ZSL-30t,
ZSGB-A-5t,ZSGB-A-10t,ZSGB-A-15t,ZSGB-A-20t,ZSGB-A-25t,ZSGB-A-30t,ZSGB-A-40t,ZSGB-A-50t。ZSGB-D-5t,ZSGB-D-10t,ZSGB-D-15t,ZSGB-D-20t,ZSGB-D-25t,ZSGB-D-30t,ZSGB-D-40t,ZSGB-D-50t,ZSGB-SS-20t,ZSGB-SS-25t,ZSGB-SS-30t,ZSGB-SS-40t,ZSGB-SS-50t。
ZSFB-D-20t,ZSFB-D-25t,ZSFB-D-30t,ZSFB-D-40t,ZSFB-D-50t,ZSFB-A-20t,ZSFB-A-25t,ZSFB-A-30t,ZSFB-A-40t,ZSFB-A-50t,
ZSKB-A-2t,ZSKB-A-3t,ZSKB-A-5t,ZSKB-A-15t, ZSKB-A-20t,ZSKB-A-25t,ZSKB-A-30t,ZSKB-A-40t,ZSKB-A-50t。ZSKB-SS-2t,ZSKB-SS-3t,ZSKB-SS-5t,ZSKB-SS-15t, ZSKB-SS-20t,ZSKB-SS-25t,ZSKB-SS-30t,ZSKB-SS-40t,ZSKB-SS-50t。